Manual J vs Manual D: what each one sizes, and how they connect

Manual J and Manual D answer different questions. Manual J works out how much heat a house gains in summer and loses in winter, for the whole house and for each room. Manual D designs the duct system that delivers the air to those rooms. They aren't two ways of doing the same job. J comes first, and its room loads are one of the things D needs before it can size a single duct.

There's a step in between. Manual S is the one that picks the equipment, using the Manual J loads and the manufacturer's performance data. ACCA, which publishes all three, says it plainly on its own blog: Manual J doesn't tell you what size equipment goes in the house, it only assesses the heat loss and gain. So the order on a real job is J, then S, then D.

The handoff from J to D is the room airflow split. Each room gets its share of the blower CFM based on its share of the load. The CFM per ton calculator does that split if you enter the room loads in Btu/h, and every row has a link that sizes the duct for that room.

Manual J, S and D side by side

What each ACCA residential manual is for
ItemManual JManual SManual D
Full nameResidential Load CalculationResidential Equipment SelectionResidential Duct Design
Question it answersHow much heating and cooling does the house need?Which equipment meets those loads?What duct sizes deliver the air to each room?
Works fromThe house itself and the local design conditionsManual J loads and the maker's performance dataRoom loads, blower data and the duct layout
Gives youWhole-house and room loads in Btu/hThe equipment to installRoom airflow and a size for every run
IRC sectionM1401.3M1401.3M1601.1

What Manual J does

Manual J is ACCA's load calculation for homes: single-family houses, small multi-unit buildings, condos, townhouses and manufactured homes. The current version is the 8th edition, published as the ANSI standard ANSI/ACCA 2 Manual J-2016.

You feed it the house. That means the walls, ceilings, floors, windows and doors, the air leakage, any mechanical ventilation, the heat from people and appliances, and where the ducts run. Ducts in a hot attic add to the load, so J counts the duct losses too. Then it sets all of that against the outdoor and indoor design conditions for your location.

What comes out is a heating load and a cooling load in Btu/h, both for the whole house (the block load) and for each room. The cooling side is split into sensible heat and latent heat, which is moisture. That's the end of Manual J's job. It doesn't size ducts, and on its own it doesn't size equipment.

What Manual D does

Manual D is ACCA's duct design standard for homes, published as ANSI/ACCA 1 Manual D-2016 (3rd edition). It applies to every common duct material, including sheet metal, duct board and flex.

It starts from the equipment Manual S picked. The blower table gives the airflow at a given external static pressure. Take away what the coil, filter, grilles, registers and dampers use, and what's left is the available static pressure for the ducts. Add up the total effective length of the longest run, which is the straight duct plus the equivalent length of every fitting. Then the design friction rate is the available static times 100, divided by that total effective length. The friction rate guide walks through each piece.

Next, each room gets its airflow: room CFM = blower CFM × room load ÷ total load. Manual D does this for heating and for cooling, and each room is designed for the larger of the two. With the room CFM and the friction rate in hand, every branch and trunk gets sized, and the velocity gets checked so the system isn't noisy.

A worked handoff from room loads to duct sizes

Here's how the numbers flow, using example figures only. Say Manual J gives cooling loads of 12,000, 8,000 and 4,000 Btu/h for three parts of the house, 24,000 in total. Say the equipment from Manual S moves 1,200 CFM at the static pressure you have, read off its blower table. And say 0.12 in. w.g. is left for the supply ducts over a 150 foot effective run, so the design friction rate is 0.12 × 100 ÷ 150 = 0.08.

Example only: galvanized round duct at 0.08 in. w.g. per 100 ft, standard air
RunShare of loadAirflowExact sizeStock sizeVelocity at stock size
TrunkAll1,200 CFM15.4 in.16 in.859 fpm
Area 112,000 of 24,000600 CFM11.9 in.12 in.764 fpm
Area 28,000 of 24,000400 CFM10.2 in.12 in.509 fpm
Area 34,000 of 24,000200 CFM7.9 in.8 in.573 fpm

Estimates only: they can differ from your chart or the manufacturer's data by 5% or more (flex by 2 times or more), so verify accuracy for your own application against the design documents, manufacturer data and local code.

Area 2 is the interesting one. 10.2 inches falls between a 10 and a 12 on the calculator's stock list. A 10 inch at 400 CFM runs about 0.089 per 100 feet, a little over the 0.08 you planned, at 733 fpm. Whether that's fine depends on how much static you have to spare. Rounding duct sizes goes through that call.

Take Manual J out and there are no room loads to split the air by. Take Manual S out and there's no blower table, so the 1,200 CFM is a guess. You can run the sizing yourself in the duct size calculator.

Do you need both? What the code says

The International Residential Code covers both. Section M1401.3 says heating and cooling equipment shall be sized in accordance with ACCA Manual S, based on loads calculated with ACCA Manual J or other approved methods. Section M1601.1 says duct systems shall be installed in accordance with that section and ACCA Manual D or other approved methods.

Two things to keep in mind. First, the code allows other approved methods, so check what your jurisdiction accepts. Second, enforcement varies a lot. A North Carolina state code article put it this way: some agencies want the calculations before a permit is issued, some before the final inspection, and some don't ask at all. Call your building department before you price the job.

So yes, you need both, because they do different work. A Manual J with no duct design leaves the airflow to guesswork. A duct design with no Manual J has nothing to split the air by.

Where the rules of thumb fit

You'll hear 400 CFM per ton and a friction rate of 0.08 to 0.10. Both are common starting points, and this site's calculators use 400 and 0.08 as defaults. They're fine for a rough check or a quick look at an existing duct. They aren't a design. ACCA's blog warns against the idea that required CFM is the floor area times some magic number, or that a given duct size always carries a set CFM. When the job has a Manual J and Manual D, those numbers win. The CFM per ton guide covers when to move off 400.

On a replacement, the ducts are already in the walls. If the customer complains about noise or rooms that never get comfortable, ACCA's blog points to Manual D as the tool for tracking down airflow and duct problems. The same blog lists short cycling and trouble controlling humidity among the complaints that call for a fresh Manual J.

Frequently asked questions

What is the difference between Manual J and Manual D?

Manual J calculates the heating and cooling loads for the house and each room, in Btu/h. Manual D designs the ducts: it sets the friction rate from the blower data and the longest run, splits the airflow by room load, and sizes every run. J's room loads are one of D's inputs.

Does Manual J size the ducts?

No. Manual J counts duct heat loss and gain as part of the load, but it doesn't size anything. Equipment is selected with Manual S, and ducts are sized with Manual D.

Is a Manual J required by code?

The International Residential Code, section M1401.3, calls for equipment to be sized with Manual S from loads calculated with Manual J or another approved method. Whether and when your local building department asks to see it varies, so check with them.

Which comes first, Manual J, S or D?

Manual J first, for the loads. Then Manual S, to pick equipment that meets those loads using the maker's data. Then Manual D, which uses the equipment's blower data and the room loads to design the ducts.

More articles

All articles